BVMKF - GLOSS HIGH SOLID POLYURETHANE, 6407
- MSDS: BVMKF
- Manufacturer: CARDINAL INDUSTRIAL FINISHES
- Product Name: GLOSS HIGH SOLID POLYURETHANE, 6407
- National Stock Number: 8010-00N052489
Product Identification
Product ID:GLOSS HIGH SOLID POLYURETHANE, 6407
MSDS Date:06/30/1994
FSC:8010
NIIN:00N052489
MSDS Number: BVMKF
Responsible Party
SOUTH EL MONTE, CA 91733
US
Emergency Phone: 800-424-9300 (CHEMTREC)
Info Phone: 818-444-9274;213-283-9335
Preparer: BOB SYPOWICZ
Cage: 65860
Contractor
Telephone: 818-444-9274 OR 213-283-9335
Cage: 65860
Ingredients
70
CAS: 78-93-3
RTECS: EL6475000
Fraction By Weight: 2%
OSHA PEL 200 PPM
ACGIH TLV: 200 PPM/300STEL
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
2.1 @20C.
CAS: 110-43-0
RTECS: MJ5075000
Fraction By Weight: 15%
OSHA PEL 100 PPM
ACGIH TLV: 50 PPM
ACETIC ACID, BUTYL ESTER; (N-BUTYL ACETATE) (SARA III).
CAS: 123-86-4
RTECS: AF7350000
Fraction By Weight: 10%
OSHA PEL 150 PPM
ACGIH TLV: 150 PPM/200STEL
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
VOLATILE ORGANIC COMPOUNDS AS PAINT
RTECS: 9999999VO
OSHA PEL N/K
ACGIH TLV: N/K
VOLATILE ORGANIC COMPOUNDS MIXED 4 TO 1 W/340HP
RTECS: 9999999VO
OSHA PEL N/K
ACGIH TLV: N/K
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:EYES:CAN CAUSE IRRIT & REDNESS,
TEARING/BLURRED VISION. SKIN:MOD IRRIT POSS FROM PRLNGD EXPOS,
DEFAT & DERM. INHAL:NASAL IRRIT, HDCH, DIZZ, NAUS, WEAKNESS/VOMIT,
LOSS OF CONSCIOUSNESS. INGEST:GI IRRIT, HDCH, DIZZ, NAUS,
WEAKNESS/VOMIT.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:PRE-EXISTING RESPIRATORY CNDTNS,
PRE-EXISTING SKIN DISORDERS, LIVER AND KIDNEY DISORDERS.
First Aid
First Aid:EYES:FLUSH W/WATER FOR 15 MINS. GET MED ATTN IMMED. SKIN:WASH
EXPOSED AREA W/SOAP & WATER. REMOVE CONTAMD CLTHG. INHAL:REMOVE TO
FRESH AIR. IF BRTHG IS DIFFICULT, ADMIN OXYG. IF BRTHG HAS STOPPED,
GIV E ARTF RESP. GET MED ATTN. INGEST:DO NOT INDUCE VOMIT, KEEP
PERSON WARM AND QUIET. GET MED ATTN.
Fire Fighting
Flash Point Method:TCC
Flash Point:24.0F,-4.4C
Lower Limits:1.1%
Upper Limits:11.4%
Extinguishing Media:FOAM, DRY CHEMICAL, CARBON DIOXIDE, WATER FOG.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA W/FULL FACE PIECE
OPERATED IN A PRESSURE DEMAND OR OTHER POSITIVE PRESSURE MODE.
Unusual Fire/Explosion Hazard:CNTNRS MAY DEFORM/EXPLODE WHEN EXPOSE TO
EXTREME HEAT. DECOMPOSITION PRODUCTS MAY YIELD OXIDES OF CARBON AND
NITROGEN.
Accidental Release
Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES. ABSORB LIQUID
IN ABSORBANT MATL AND PREVENT SPREADING TO GROUND WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:CNTNRS OF THIS MATL MAY BE HAZ WHEN
EMPTIED. SINCE EMPTIED CNTNRS RETAIN PROD RESIDUALS (VAP, LIQ,
AND/OR SOLID) ALL HAZARD PRECAUT MUST BE OBSERVED.
Other Precautions:PAINT & SOLV HAVE BEEN LINKED TO LIVER ABNORMALITIES,
KIDNEY & LUNG DMG. ALTHOUGH THIS COATING IS WATERBORNE OF LOW TOX,
FOLLOW PRECAUT TO PREVENT OVEREXPOSURE.
Exposure Controls
Respiratory Protection:IF TLV OF PROD/ANY COMPONENT IS EXCEEDED,
NIOSH/MSHA JOINTLY APPRVD AIR-SUPPLIED RESP IS ADVISED IN ABSENCE
OF ENVIRON CONTROL. OSHA REGS ALSO PERMIT OTHER NIOSH/MSHA RESPS
UNDER SPECIFIED CNDTNS. ENG INEERING/ADMINISTRATIVE (SUPDAT)
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL AND/OR LOCAL
EXHAUST) VENT TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:OSHA APPRVD CHEM SPLASH GOGGLES.
Other Protective Equipment:PVNT RPTD/PRLNGD SKIN CONT W/GB PROT HAND
CREAM, WEAR IMPERVIOUS CLOTHING AND CHEMICAL RESISTANT BOOTS.
Work Hygienic Practices:WASH HANDS BEFORE EATING OR USING REST ROOM.
SMOKE IN SMOKING AREAS ONLY.
Supplemental Safety and Health
RESP PROT:CONTROLS SHOULD BE IMPLEMENTED TO REDUCE EXPOS. WHEN COATING
IS CATALYZED, LOW LEV OF ISOCYANATES ARE PRESENT. IN LIEU OF AIR
MONITORING DATA, NIOSH/MSHA AIR SUPPLIED RESPS ARE SUGGESTED FOR
SPRAY APPLICATIONS.
Chemical Properties
Boiling Pt:B.P. Text:>175F,>79C
Vapor Pres:SEE INGS
Vapor Density:HVR/AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NOT KNOWN
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:46-48
Stability
Stability Indicator/Materials to Avoid:YES
AVOID CONTAMINATION W/ALKALIS AND STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME TEMPERATURES.
Hazardous Decomposition Products:WHEN MIXED W/CATALYST, PROD WILL REACT
W/WATER, ALCOHOLS AND AMINES.
Disposal
Waste Disposal Methods:DESTROY BY LIQ INCIN I/A/W APPLIC REGS. CONTAMD
ABSORBANT SHOULD BE INCINERATED OR SENT TO APPRVD LANDFILL I/A/W
LOCAL, STATE, AND FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.